Schroth Harness for the Ralliart (and Evo X; that's right, RA Listed First)

[sstevojr]

Thanks to RRE for the hook-up! These are designed to be direct bolt-on for RA's (and Evo X's).
The kit comes with additional bolts, but here is how I installed mine using stock bolt holes (based on the guidance of Mike W of RRE):
Driver's Seat Belt Bolt (requires a 17mm)
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-21-01_127.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-27-45_361.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-28-12_162.jpg
Right Rear Bolt for Driver's Seat (next to center console, requires a 14mm)
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-21-16_137.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-21-28_647.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-35-47_840.jpg
Remove the Back Seat (two clips)
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-38-25_65.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-38-31_654.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-38-39_843.jpg
Several Bolts to Choose From
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-38-50_641.jpg
Driver's Side Seat-Back (to clear the seat bottom when re-installed; 14mm, the tabs are designed to be "bent" to accommodate tight spaces)
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-42-44_184.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-42-49_913.jpg
Rear Driver's Side/Center Seat Belt Clips
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-51-17_529.jpg

END RESULT:
DD
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_18-00-39_392.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-59-02_120.jpg
READY FOR WORK
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-59-43_862.jpg

[R-EVOLUTION]

Looks good and nice info...

[Muellerized...]

Thanks to RRE for the hook-up! These are designed to be direct bolt-on for RA's (and Evo X's).
The kit comes with additional bolts, but here is how I installed mine using stock bolt holes (based on the guidance of Mike W of RRE):
Driver's Seat Belt Bolt (requires a 17mm)
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-21-01_127.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-27-45_361.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-28-12_162.jpg
Right Rear Bolt for Driver's Seat (next to center console, requires a 14mm)
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-21-16_137.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-21-28_647.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-35-47_840.jpg
Remove the Back Seat (two clips)
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-38-25_65.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-38-31_654.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-38-39_843.jpg
Several Bolts to Choose From
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-38-50_641.jpg
Driver's Side Seat-Back (to clear the seat bottom when re-installed; 14mm, the tabs are designed to be "bent" to accommodate tight spaces)
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-42-44_184.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-42-49_913.jpg
Rear Driver's Side/Center Seat Belt Clips
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-51-17_529.jpg

END RESULT:
DD
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_18-00-39_392.jpg
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-59-02_120.jpg
READY FOR WORK
http://i902.photobucket.com/albums/ac226/steckers/2012-09-03_17-59-43_862.jpg

Please mount the tunnel side of your lap belt to the factory location, as the perpendicular to the load path mounting you currently have is not safe, thank you.

If you need any clarification, please call my office.

[blkside]

True story... The Mounts need to face the direction of loading so having the brackets facing the outside of the car is "AFU"... and you can go to the schroth website and it is not only ok but actually recommended to put contour bends in the mounts for proper alignment...

[sstevojr]

I wasn't sure how crucial that one was, as the tabs can bend. The real PITA is that it seems the seat needs to be removed to get that bolt all the way out :(
But looking at the instructions, it appears using a bolt on the sliding rails is acceptable?

[amaev05]

u should use the original tunnel side bolt. 2 reasons. 1 the tabs must be in line with the belts when you are in the seat. if not they will bend and you will not be held in place. 2. the lap belt must keep you down not just held back, you will submarine right under it, in a head on collision.

[amaev05]

other than that, looks awesome.

[sstevojr]

Your a few days late, but thanks just the same ;)